博客中心思想:GPU已经变得如此强大，以至于人们开始用它来完成立体视觉和通用计算等任务。学习如何运用它们，推荐Wolfgang Engel的ShaderX3: Advanced Rendering with DirectX and OpenGL和Matt Pharr，Randima Fernando，以及为此做出贡献的20多名研究人员的GPU Gems 2: Programming Techniques for High-Performance Graphics and General-Purpose Computation。 作者: SSforME 时间: 2021-8-14 22:19
Graphics Synthesizer, GPUs, and Dual Cores
It was apparent early on the project that the GS plugin was going to be a big bottleneck during 3D scenes. It isn’t that the GS plugin itself does a lot of computation on the CPU, but the fact that it needs to communicate with the graphics card means that unnecessary stalls will occur in the graphics driver as the GPU and CPU are synchronized. During these stalls, the CPU basically goes to lunch until the GPU is ready. Graphics drivers and libraries are aware of this and try as little as possible to communicate with the graphics card. They usually cache render state changes, shader changes, and texture changes up until actual geometry is rendered. They also take advantage of FIFOs (first in first out buffers). The CPU just writes to the FIFO and the GPU just reads from it, this makes all the difference in terms of keeping the GPU active while the CPU isn’t and vise versa.
The biggest challenge when designing games and hardcore applications that need to use the GPU to its full potential is to make sure that graphics driver stalls are minimal at all costs. What kills games isn’t sending geometry down the graphics pipeline, but it is when render targets are switched, render targets are used as textures in the next draw call, textures are locked, and when render targets are transferred from GPU memory to CPU memory (in the last case, the CPU not only goes to lunch, but has dinner also). GPU optimization talks usually appear in every Game Developers Conference and there are many papers on them on the net, so there is a lot more to the story than written here.
All this means is that single-threaded applications really need to design their GPU algorithms well to see fast frame rates. This unfortunately is not possible with Pcsx2 and the GS plugin. The GS plugin has to draw geometry in the same order as it was received. This kills almost all caching techniques used by modern games because the GS and PC GPUs have very different performance bottlenecks. In modern GPUs, it is advantageous to group as much geometry as possible in one draw call. The GS doesn't suffer from such bottlenecks. The GS also has two different contexts which makes things twice as difficult. ZeroGS can only do a limited amount of work-arounds before compatibility starts dropping, so the only other option is to try to multithread the GS. Note that using graphics libraries from multiple threads is not a trivial task.
Fortunately, the GS plugin is very unique in its nature. 99% of the communication that happens between the GS plugin and the rest of the systems components happens in the direction to the GS. The only times the EE needs to synchronize with the GS is when it reads back the FINISH/SIGNAL registers and part of the 4Mb GS memory. Register readbacks are used frequently, so this suggests that tight synchronization will be needed with the GS. The GS memory readbacks aren't as frequent; however, they require some special considerations with Virtual Memory and DMAs. The rest of the 99% of communication that goes to the GS happens with a GS FIFO.
When first started, Pcsx2 creates a GS thread and reserves special memory for the GS FIFO. The GS plugin then creates the Direct3D device/GL context only for that thread. Then when the game runs, the EE copes all its GS packets to the FIFO and then notifies the GS thread. The GS thread then checks if the FIFO has data, and then sends it to the GS plugin. This sounds easier than it actually is because very tight synchronization needs to happen to make sure no overwriting occurs in the FIFO. The FINISH/SIGNAL register synchronization actually doesn’t happen across the EE and GS thread boundaries. Instead the EE thread peeks at all the packets ahead of time and handles it in its own routines.
What makes the “Dual Core” option special is the notifies part of the last explanation. The GS thread can either sleep waiting for a notification from EE, which can be done by WaitForSingleObject and SetEvent functions. Or it can continually check if the GS FIFO is empty without ever stopping. The latter option kills single cores but goes much faster on dual cores. The results of clicking on the MTGS and DC options on dual cores are phenomenal. Usually frame rates go up or even surpass 2x.
Multithreading in games is going to be very big in the future. The times have passed when there is one CPU that does everything and one GPU that just renders. The biggest problem is which game processing to divide into which thread, and how these threads will communicate with each other. Many of these issues are still open and current game companies are struggling with the added complication of concurrent execution.
Moral of the blog GPUs have become so powerful that people are staring to do tasks like stereo vision and general purpose computation with them. Learn how to use them. I recommend
ShaderX3: Advanced Rendering with DirectX and OpenGL by Wolfgang Engel and GPU Gems 2: Programming Techniques for High-Performance Graphics and General-Purpose Computation by Matt Pharr, Randima Fernando, and the 20+ researchers that contributed to it. 作者: yangjuniori 时间: 2021-8-16 20:23
posted by wap, platform: Chrome
PS2一些游戏在读盘的时候突然会显示半个场
